Plastic and nonmetallic article shaping or treating: processes – Mechanical shaping or molding to form or reform shaped article – Shaping against forming surface
Reexamination Certificate
2011-06-07
2011-06-07
Del Sole, Joseph S (Department: 1743)
Plastic and nonmetallic article shaping or treating: processes
Mechanical shaping or molding to form or reform shaped article
Shaping against forming surface
C264S328900, C264S334000, C249S064000, C249S107000, C249S126000, C249S134000, C249S160000, C425S577000, C425S468000
Reexamination Certificate
active
07955546
ABSTRACT:
In the assembly-completed state, the Lower Mold, the Outer Mold, the Upper Mold, and the “inner mold (the integral body of the Pin-holder and the Pin)” are stacked and fixed in this order from the bottom, and the Pin is coaxially inserted into the First Hole of the Outer Mold and the Second Hole of the Upper Mold. In the assembly-completed state, the molding space for molding the ceramic molded body is formed between the surface of the Pin and the First Hole, and the annular minute gap is formed between the surface of the Pin and the Second Hole. The ceramic slurry poured into the Slurry Reservoir Pres formed on the upper surface of the Upper Mold falls and flows into the molding space through the annular minute gap by virtue of the action of gravity or the like.
REFERENCES:
patent: 30054 (1860-09-01), Evans
patent: 2201777 (1940-05-01), Kliesrath
patent: 2341499 (1944-02-01), Cunningham
patent: 2483094 (1949-09-01), Harvey
patent: 2829400 (1958-04-01), Morin
patent: 2988765 (1961-06-01), Solomon
patent: 3293694 (1966-12-01), Taylor, Jr.
patent: 3317407 (1967-05-01), Kratzmeyer et al.
patent: 3379120 (1968-04-01), Fogle
patent: 3511845 (1970-05-01), Scalora
patent: 4017582 (1977-04-01), Naumann
patent: 4352772 (1982-10-01), Bezner
patent: 4422995 (1983-12-01), Schad
patent: 4552716 (1985-11-01), Habich
patent: 5243874 (1993-09-01), Wolfe et al.
patent: 5780079 (1998-07-01), Lee
patent: 6887417 (2005-05-01), Gawreluk et al.
patent: 7419626 (2008-09-01), Mark
patent: 2003/0160362 (2003-08-01), Fithian
patent: 2004/0130070 (2004-07-01), Abels et al.
patent: 2005/0006819 (2005-01-01), Weihrauch
patent: 2005/0156347 (2005-07-01), Haas et al.
patent: 2005/0172439 (2005-08-01), Weihrauch
patent: 2005/0287319 (2005-12-01), Miyazawa et al.
patent: 2006/0216446 (2006-09-01), Neil et al.
patent: 2007/0054003 (2007-03-01), Reis et al.
patent: 2007/0126138 (2007-06-01), Dooley et al.
patent: 2008/0048356 (2008-02-01), Kitayama et al.
patent: 2009/0029087 (2009-01-01), Ohashi et al.
patent: 55014153 (1980-01-01), None
patent: 56135046 (1981-10-01), None
patent: 05-121148 (1993-05-01), None
patent: 08-062106 (1996-03-01), None
patent: 11-042619 (1999-02-01), None
patent: 2004/035281 (2004-04-01), None
patent: 2007/111380 (2007-10-01), None
Imaeda Minoru
Ishibashi Satoshi
Okabe Yosuke
Yoshioka Kunihiko
Bodawala Dimple
Burr & Brown
Del Sole Joseph S
NGK Insulators Ltd.
LandOfFree
Forming die and method for manufacturing formed body using... does not yet have a rating. At this time, there are no reviews or comments for this patent.
If you have personal experience with Forming die and method for manufacturing formed body using..., we encourage you to share that experience with our LandOfFree.com community. Your opinion is very important and Forming die and method for manufacturing formed body using... will most certainly appreciate the feedback.
Profile ID: LFUS-PAI-O-2696532