Illumination – Housing – Recessed
Reexamination Certificate
1999-07-22
2002-02-26
O'Shea, Sandra (Department: 2875)
Illumination
Housing
Recessed
C362S147000, C362S373000, C362S294000
Reexamination Certificate
active
06350046
ABSTRACT:
TECHNICAL FIELD
The invention is primarily designed for use with one or more fluorescent lamps because of their widespread popularity, but accommodates any type of lamp which requires an auxiliary power stabilizing circuit.
BACKGROUND ART
In addition to fluorescents, commonly used alternative lighting of this type includes low voltage halogen lamps, and high intensity discharge (HID) lamps, both of which are more compact and efficient than incandescents. All of these lamps require a circuit device to condition the power, as they will not operate on the U.S. standard, 110 volts at 60 Hz. current. In this specification, the lamps will be described as “fluorescent”, and the power stabilizing circuit as the “ballast”, but it will be understood that the term “fluorescent” refers generically to any lamp which requires an on-board (or auxiliary) device or circuit to stabilize the current or the voltage, or both, and such circuit or device is covered by the term “ballast”. The ballast converts the local power, whether it be AC, DC, 110-Volt, 277-Volt or whatever, to the form for which the lamp and system were designed, so the same lamp is used everywhere, with the electronics being the adaptive factor.
With the advantage of more efficiency, these lamps come with the baggage of the auxiliary circuit requirement, and an inherent circuit overheating problem. Heat damage will result from continued exposure to the hot cathodes of the lamp, especially if the circuit is enclosed in the same housing as the lamp. Although the subject lamps are more efficient than incandescents by a factor of up to eight or ten to one, nonetheless up to 75% of the energy they consume is dissipated as heat. And whereas manufacturers recommend that the ambient temperature be no higher than 40 degrees centigrade, and never greater than 50 degrees, studies have shown that in a recessed ceiling can, temperatures around the upper area where the ballast would be, routinely exceed 70 degrees centigrade in a 25-degree room using a 27-watt fluorescent. Higher wattage mean commensurately higher temperatures. In that temperature range, circuit life is halved for every 10 degree-rise in temperature due to cumulative heat-induced insulation deterioration.
This disclosure specifically addresses ceiling-mounted fixtures, including “cans” recessed behind the ceiling panels. Retrofitting these cans to accept fluorescent lighting, or other lighting which is more efficient than incandescent, presents several problems. For one thing, the compact fluorescent lamps and adapters which are designed to replace light bulbs are generally too long to fit within the can and extend out slightly beyond the housing in ceiling-mount installations with vertical lamps. The can's translucent diffusion covers may have to be removed, resulting in the creation of both glare and aesthetic problems, which present obstacles to upgrading hotel corridors, lobbies and rooms and other large commercial establishments whose multiplicity of can installations cry for conversion to low-energy lighting.
If the ceiling can is a side-mount version designed to use a horizontally extended incandescent bulb, the typical compact fluorescent adaptor and lamp designed for retrofitting will not fit at all, since the tube does not have the option of extending beyond the boundary of the can. There are cans designed specifically for housing fluorescent replacements, but making these installations as retrofit conversions is very labor intensive and expensive. Worse, when finished the ballasts are still at the hot end of the can, still subject to premature failure from continuous exposure to heat not only from the lamp but from hot pipes and other equipment that is found between the ceiling joists. Upgrading often cannot be economically justified by lower utility bills, even without considering the reduced lamp and ballast life expectancy.
Much of the heat problem is caused by the practice of using standard compact fluorescent adapters which have the ballast around the base. Heat is also generated by the ballast itself, although this heat is dwarfed by the heat output of the lamp. These base-mounted units work fine for floor and ceiling lamps where there is adequate ventilation and the lamp base housing the electronics is below, not above, the hot lamp. But an inverted can, even though provided with ventilation holes, accumulates heat to destructive levels. This problem is aggravated by the fact that electronic ballasts, which replace the older coiled wire transformer-type ballasts, are much more sensitive to heat than traditional ballasts. The newer design has advantages in efficiency, reduced volume and weight, and inherent packaging versatility stemming from the ability to separate the components into different areas of the mounting fixture for compactness. These advantages lead to the use of electronic ballasts in applications for which they are not suited.
It is probably relatively rare for a construction salesperson to advise the building owner, responsible for authorizing an upgrade, of these problems, which skewer the economic balance even more against replacement.
Due to these problems, although hotels and other commercial establishments are slowly converting to reduced power consumption lighting, still only a small fraction of the possible conversions are actually being made. With a clear cost disadvantage of upgrading in some installations, it is difficult for the establishment to justify to the shareholders the changeover as part of its duty as a world citizen. There is a need for a simple retrofit unit which will enable can-mounted lighting to take full advantage of the economics of fluorescent tubes by preventing premature burn-out of electronic ballasts. There is also a need for newly designed recessed light fixtures that use fluorescent bulbs and/or require a power stabilizing circuit such as a ballast.
DISCLOSURE OF INVENTION
The instant invention fulfills the above-stated need by providing specially designed recessed lamp fixtures which come in several variations, but in all instances having a ballast compartment housed separately from the lamp housing. In addition to separation of the ballast from the lamp housing, several other design features keep the ballast cool. In one embodiment the passageway between the ballast and the lamp is preferably home to a moving air curtain which continuously draws up cool air alongside the ballast, driven by lamp-induced heat convection. In this embodiment the ballast is beneath the lamp if practicable, therefore it is substantially upwind from the hot airflow generated by the electrodes or filament, rather than immersed in it immediately above the hottest part of the lamp, as is traditional. Cooling air passes up around the ballast first, before it reaches the lamp, and then into the can, accumulating in the upper part where it dissipates by conduction, radiation and convection through ventilation holes.
One recessed can design has a ballast compartment which is separated from the rest of the fixture and is mounted in an annular ring flush against the bottom surface of the ceiling around the lamp opening. This rim-mounted circuit connects to the fluorescent base mounting socket, diverting incoming power from the power company and delivering it to the lamp in useable form. This version embodies the essential features of the invention wherein the ballast is separate from, and in fact does not even share a compartment with, the lamp, and a corridor for an air curtain is established between ballast and lamp.
Other forms of recessed lamp fixtures specifically designed for use with electronic ballast lamps have a separate ballast housing made of heat insulating material and whose only opening is in its bottom wall. The ballast housing is located remotely from the interior of the light source housing and/or a reflector housing. A heat sink structure is mounted in the bottom opening of the ballast housing to draw heat away from the power stabilizing circuitry. The heat sink structure may take the form of a cosmetic trim cove
Logan II Charles C.
Neils Peggy A
O'Shea Sandra
LandOfFree
Light fixture does not yet have a rating. At this time, there are no reviews or comments for this patent.
If you have personal experience with Light fixture, we encourage you to share that experience with our LandOfFree.com community. Your opinion is very important and Light fixture will most certainly appreciate the feedback.
Profile ID: LFUS-PAI-O-2936384