Measuring and testing – Internal combustion engine or related engine system or... – Compression
Reexamination Certificate
1999-10-28
2003-09-23
McCall, Eric S. (Department: 2855)
Measuring and testing
Internal combustion engine or related engine system or...
Compression
C073S115060
Reexamination Certificate
active
06622549
ABSTRACT:
BACKGROUND OF THE INVENTION
Four stroke direct-injection engines have been under recent intense development for both diesel and gasoline fuel applications due to significant fuel economy improvements and reduced emission levels in comparison to engines with conventional fuel injection. Direct injection diesel engines have a higher baseline thermal efficiency (about 40% peak), 20-35% better fuel efficiency, 10-20% lower CO
2
emissions, near-zero evaporative emissions, and low cold-start emissions. Fuel economy improvements of as much as 35% have been recently reported, combined with a simultaneous increase in engine power and torque of 10%, for a direct gasoline injection engine. Such remarkable performance has been realized through a combination of very lean burn combustion (Air-fuel ratios as high as 40:1) and stratified charge mixing inside each engine combustion chamber.
SUMMARY OF THE INVENTION
A key component that is required for both Direct Diesel Injected (DDI) and Direct Gasoline Injected (DGI) engines is an accurate and cost-effective fuel injector. In diesel engines, the new injection must operate at extremely high pressures (as high as 30,000 psi), provide accurate and repeatable spray patterns, and be precisely timed. In addition, such an injector must operate for as many as 0.5 million miles and be of low cost.
In DGI applications, in particular, the very poor lubricating nature of gasoline and critical injector specifications make gasoline injectors difficult and expensive to manufacture.
To provide the required performance, reliability, and low-cost for both DDI and DGI injectors, disclosed below are approaches based on closed loop control of injector operating parameters, where combustion chamber and fuel pressures are used as control parameters. As detailed below a preferred way of obtaining these two pressures is to integrate two miniature fiber optic pressure sensors inside an injector. Such a “smart” injector does not need to be individually calibrated, as currently done, so its price can be significantly lower. Differences caused by manufacturing variability, aging, pressure line fluctuations, or fuel quality can be compensated for by using closed-loop control of fuel injection timing, duration and pressure. The combustion chamber pressure sensor of the smart injector provides, in addition, real-time information about cylinder pressure including peak pressure (PP), indicated mean effective pressure (IMEP), start of combustion (SOC) and location of peak pressure (LPP). When inputs from both fuel and combustion pressure sensors are used to control the injector, simultaneous benefits of reduced emissions, improved fuel economy, increased injector reliability, and reduced cost can be achieved.
INVENTION OVERVIEW
The fiber optic sensors utilized in the smart injector are of a novel construction aimed at high accuracy in a very small device exposed to extremely high pressures and temperatures. The sensor tip may be as small as 2.5 mm in diameter or smaller. By using a specially shaped diaphragm in the sensor and two D-shaped optical fibers, high levels of optical modulation can be realized at small diaphragm deflections. Small diaphragm deflections are required to permit high diaphragm yield strength and long fatigue life. Using a two photodiode detection technique, each sensor's signal interface/conditioner can operate accurately over a temperature range of −50 to 150° C.
In a preferred configuration two types of sensors are used in the smart injector: (1) a high pressure sensor for monitoring static fuel pressures inside the injector and (2) a sensor for detecting dynamic combustion chamber pressures.
To compensate for changing sensor response with temperature, a temperature compensation technique utilizes a combination of a thin film deposited on the diaphragm inner surface and a temperature probe mounted in the sensor housing. The thin film reflection coefficient changes with temperature thereby compensating for any intra cycle (short term) diaphragm temperature excursions above its average temperature. Any longer term errors, resulting from increased diaphragm deflection at higher average temperature and other thermal effects on the sensor head, are compensated for by adjusting the pressure sensor's gain, based on the temperature probe output.
While most direct injectors require dynamic fuel pressure information, only static pressures must be known in such approaches as fuel rails. Disclosed below is a static pressure sensor utilizing two optical fiber pairs, with one pair acting as a reference device to compensate for errors that may result from temperature effects on opto-electronic components, fiber bending, or other sources of undesirable light intensity fluctuations.
As above, to compensate for errors arising from intra-cycle diaphragm heating due to the nearby combustion gasses, the compensation technique is similar to the technique used for dynamic sensors. For the static sensor one pair of fibers is exposed to diaphragm deflection and the other pair of fibers is installed in front of a non-deflecting reflector coated with a reflection temperature dependent thin film. A separate temperature probe provides input information for additional compensation for sensor gain and offset changes arising from varying inter-cycle average diaphragm and housing temperatures.
REFERENCES:
patent: 4459477 (1984-07-01), Asawa et al.
patent: 4493208 (1985-01-01), Grover
patent: 4620093 (1986-10-01), Barkhoudarian et al.
patent: 4753109 (1988-06-01), Zabler
patent: 4781059 (1988-11-01), Suzuki et al.
patent: 4891640 (1990-01-01), Ip
patent: 4932262 (1990-06-01), Wlodarczyk
patent: 5390546 (1995-02-01), Wlodarczyk
patent: 5394852 (1995-03-01), McAlister
patent: 5421195 (1995-06-01), Wlodarczyk
patent: 5452087 (1995-09-01), Taylor et al.
patent: 5600070 (1997-02-01), Wlodarczyk
patent: 5600125 (1997-02-01), Poorman et al.
patent: 5831263 (1998-11-01), Komachiya et al.
patent: 5834629 (1998-11-01), Hammarberg
patent: 5978525 (1999-11-01), Shu et al.
patent: 6135760 (2000-10-01), Cusack et al.
patent: 6155212 (2000-12-01), McAlister
Poorman Thomas J.
Wlodarczyk Marek T.
Deimen James M.
McCall Eric S.
LandOfFree
Fuel injectors with integral fiber optic pressure sensors... does not yet have a rating. At this time, there are no reviews or comments for this patent.
If you have personal experience with Fuel injectors with integral fiber optic pressure sensors..., we encourage you to share that experience with our LandOfFree.com community. Your opinion is very important and Fuel injectors with integral fiber optic pressure sensors... will most certainly appreciate the feedback.
Profile ID: LFUS-PAI-O-3034788