Ships – Valves – Boat plugs
Reexamination Certificate
2001-03-26
2002-11-12
Sotelo, Jesus D. (Department: 3617)
Ships
Valves
Boat plugs
C114S18300R
Reexamination Certificate
active
06477971
ABSTRACT:
BACKGROUND OF THE INVENTION
Many power boats have a manual drain plug located in a through-transom hole in the transom, near the base of the transom and extending through the hull to the rearmost area of the bilge. As a boat undergoes normal usage, it inevitably takes on water which accumulates, and which ultimately works its way down to the bilge. The through-transom drain plug is designed to be removed when the boat is taken out of the water to permit the bilge to drain. For trailered boats, this is a primary means of draining bilge water, and the plug is removed nearly every time the boat is taken out of the water. Gravity will cause the water to flow out of the boat, and will be most effective when the boat is positioned with the through-transom hole at a point that is lower than the interior of the bilge. In larger or non-trailered boats the primary means for bilge drainage may be a bilge pump, although when the boat is hauled for storage, maintenance, or repair, it is common for the through-transom drain plug to be removed, both to drain any water that may be in the bilge, and to provide an exit for rain or other water that may collect in the interior of the boat during storage, maintenance, or repair.
A common method of sealing the through-transom hole during normal boat usage is with an external, threaded plug. When the boat is out of the water, the plug is easily accessible and can be removed using only a wrench. While this method of boat drainage is simple and easy, it has at least two major drawbacks, either of which has been experienced by many, if not most small boat owners at sometime during their lives. First, because the plug is not sealing the drain hole when the boat is out of the water, it must be inserted into the drain hole before the boat is launched. If is it not, the boat will immediately begin to take on water when launched, and the amount of water taken on will depend only upon how long the drain hole has been submerged before the condition is discovered. When the condition is discovered, the boat must immediately removed from the water, if possible, allowed to drain, and the manual plug inserted. If the boat has taken on too much water before the condition was discovered, it may not be possible to remove it from the water using the same means as were used to launch it, and more elaborate and expensive steps to remedy the condition must be used. In addition, when water reaches a critical level in the boat, electrical components and batteries may be adversely affected, and fuel, oil, and other materials may spill and cause environmental damage.
A second drawback to using the standard drain plug is that, in the event that the boat takes on water while afloat and away from land, the water cannot be drained through the drain hole, but must be emptied using an electric or manual bilge pump. Even though a boat planing through the water could theoretically drain its bilge through the drain hole, it is difficult if not impossible for the externally threaded plug to be removed during high speed planing. When a boat capable of high speed plaining does begin to take on water, it must rely solely upon its bilge pump to remove the water and alleviate a potentially dangerous condition. If, for any reason, the bilge pump is inoperable, such as a failure of the boat's electrical system, a merely inconvenient condition can quickly develop into a life-threatening one. Accordingly, there is a need for a bilge drainage system that can be manually operated from inside a boat while the boat is otherwise operable.
SUMMARY OF THE INVENTION
The bilge drainage system of this invention uses a permanent internally-mounted stopcock to provide an open through-transom drain hole that may be manually operated while the boat is riding on a plane. The planing motion of the boat orients the hull such that the base of the transom is at a point that is below the bilge. While planing, bilge water may be drained simply by opening the drainage hole. This means of drainage does not need electrical power or external access to the drainage hole, and requires only that the motor be running and the boat be capable of maintaining sufficient speed to reach a plane so that the water from the bilge may drain as a result of gravity or a pressure differential. The bilge drainage system may be included as a feature provided by the manufacturer in new boats, and may easily be retrofitted into existing boats.
REFERENCES:
patent: 3565031 (1971-02-01), DePersia
patent: 5452677 (1995-09-01), Kirkpatrick
patent: 5724908 (1998-03-01), Murray
Akerman & Senterfitt
Cesarano Michael C.
Sotelo Jesus D.
LandOfFree
Bilge drainage system does not yet have a rating. At this time, there are no reviews or comments for this patent.
If you have personal experience with Bilge drainage system, we encourage you to share that experience with our LandOfFree.com community. Your opinion is very important and Bilge drainage system will most certainly appreciate the feedback.
Profile ID: LFUS-PAI-O-2971305